Water Right Impression Series Troubleshooting Guide Page 1

Impression Series®andImpression Plus Series®Water Filters

103. MANUAL REGENERATION: Sometimes there is a need toregenerate before the control valve calls for it. This may beneeded if a period of heavy water u

START-UP INSTRUCTIONS:11• After installation is complete, rotate bypass handles to bypass mode (see Fig.2 on page 4).• Turn on water and check for lea

121. Check the media height by shining a flashlightthrough the tank to see the height of the mineral. Ifthe level is not seen, the top fill plug will

13Timer does not display time of dayA. transformer unplugged A. reconnect transformerB. no power at outlet B. repair or use working outletC. defective

14PROBLEM CAUSE CORRECTION Valve does not regenerateautomaticallywhen REGENbutton is pressedA. transformer unplugged A. connect transformer and PC boa

15REPLACEMENT PARTS:2713546FRONT COVER AND DRIVE ASSEMBLYItem No. Part No. Description Qty.1CV3540-A Black Impression®cover 1CV3540-W-A Gray Impressio

166810117 97 12423511314NOTE: For Impression Plus® Models only. Not available on 1¼ " valve.REPLACEMENT PARTS:For Impression Plus®Models OnlyPI

17REPLACEMENT PARTS:BYPASS VALVEItem No. Part No. Description Qty.1 CV3151 Nut, 1" quick connect 22 CV3150 Split ring 23 CV3105 O-ring 215 24 CV3

18INJECTOR ASSEMBLIESItem No. Part No. Description Qty.1CV3176 Injector cap 12CV3152 O-ring 135 13CV3177-01 Injector screen 14CV3010-1Z Injector assem

19REPLACEMENT PARTS:DRAIN LINE ASSEMBLY 3/4"Item No. Part No. Description Qty.1 CH4615 Elbow locking clip 12 CPKP10TS8-BULK Optional insert, 5/8&

TABLE OF CONTENTSPreinstallation Instructions for Dealers . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Bypass Valve . . . . . . . . . . .

WATER METER & METER PLUGItem No. Part No. Description Qty.1 CV3151 Nut, 1" QC 12 CV3003 Meter assembly, includes items 3 & 4 13 CV3118-01

211" PVC MALE NPT ELBOWItem No.Part No. Description Qty.CV3007 1" PVC male NPT elbow assembly 21 CV3151 Nut, 1" quick connect 22 CV3150

221-1/4" & 1-1/2" PVC SOLVENTItem No.Part No. Description Qty.CV3007-07 1-1/4" & 1-1/2" PVC solvent assembly 21 CV3151 Nut

23SPECIFICATIONS:NEUTRALIZER SPECIFICATIONSMineral cu. ft.CALCITE CALCITE CALCITE CALCITE CALCITE CALCITEor MIX 1.0 or MIX 1.5 or MIX 2.5 or MIX 1.0 o

1900 Prospect Court • Appleton, WI 54914Phone: 920-739-9401 • Fax: 920-739-9406MANUAL REGENERATIONNOTE: If you needto initiate a manualregeneratio

PREINSTALLATION INSTRUCTIONS FOR DEALERS:BYPASS VALVE:3The manufacturer has preset the water treatment unit’s sequence of cycles, cycle times, salt do

41. NORMAL OPERATION POSITION: The inlet and outlet handles point in the direction of flowindicated by the engraved arrows on the control valve. Wate

5GENERAL INSTALLATION & SERVICE WARNINGSThe control valve, fittings and/or bypass are designed to accommodate minor plumbing misalignments. There

66. INLET/OUTLET PLUMBING: Be sure to install Bypass Valve onto main control valve beforebeginning plumbing. Make provisions to bypass outside hydran

7IMS/IMB INSTALLATION INSTRUCTIONS:Special precautions must be made when connecting the drain line. Hard piping is recommended. Duringbackwash, high v

8Time of day should only need to be set after extended power outages or when daylight saving time beginsor ends. If an extended power outage occurs, t

STEP 4 – REGENERATION HOUR: The manufacturer has factory set 12:00 A.M. as the default. Thisis the hour of day for regeneration and can be reset by us